قالب وردپرس درنا توس
Home / Tips and Tricks / How to Install a Smart Lock

How to Install a Smart Lock



  A satined Smartlock from Schlager Encode on a green door.
Josh Hendrickson

When you set up a new Smarthome, one of the simplest gadgets you can add to your arsenal is a Smartlock. It's not much harder than changing a standard lock for your home. The following is to be done.

The Basics

This guide installs a Smart Lock from Encode Encode. Even if you have another Smart Lock from another brand, most (if not all) steps are the same. An intelligent lock generally has three main components: an outer part with a keyboard, a lock for a key or both, an inner part with the batteries and circuits, and the latch that secures your door. The tricky part is to connect everyone.

A quick tip: You may have been advised to test your Smart Lock before inserting it by inserting the batteries to turn it on. Then you can be sure that the lock will turn on before it is in the door.

That seems to be good advice, but the first time you turn on a smart lock, it checks to see if the door is pointing to the left or right and the latch mechanism is adjusted. Without a door that can be tested against, this can be wrong and your installation will not work properly. If you would like to perform this test, you should review the factory reset instructions. Reset the lock to factory settings after running the test.

Removing the Old Lock

Before you can install your new Smart Lock, you must remove the old lock. Standard locks are easy to remove as long as you still have access to the interior of your home. Start by finding the two screws on the inner knob. Then unscrew them.

  A standard knurled knob on a lock, with two red arrows pointing to two screws.
Josh Hendrickson

Open the door (if you have not already done so) and go to the front of the castle lock (where you plug in your key). The key assembly should be loose, pull it off.

  The key assembly of a lock, tilted slightly out of the door.
Josh Hendrickson

Now look at the side of your door for the latch that slides out when you lock it. Loosen the two screws and pull out the screw assembly.

Installing the Smart Lock

Now find the screw for your new lock and look for the top mark:

[19659006] Slide the latch into the door frame and make sure the top is facing up. Look in the door hole to see if the latch inside the door is well centered. You will notice three holes in the assembly – they should be as close to the center as possible. If this is not the case, you can extend or shorten the screw (depending on the current length) to center it. Normally you do this by turning the bolt mechanism, but you may also need to use a screwdriver instead. Then install the two screws to lock the bolt.

  A locking cavity with a bolt and lines running through the vertical and horizontal centers.
He does not have to be perfectly centered but must be perfectly centered in the area. Josh Hendrickson

Next, find the exterior mounting part for the lock. Pay attention to the long strip and the electronic cable.

  A batting encode assembly with a red box around a wire assembly and a bar.
Josh Hendrickson

Insert the assembly into your door. Pass the locking bar through the middle hole of the screw assembly. It should be the only hole through which the pole fits. Carefully push the wiring under the screw elements. You want to make sure the hardware does not adjust the cabling.

  The interior of the door lock hole shows the wiring that runs under the latch assembly.
Josh Hendrickson

If your Smart Lock assembly seems to fall out We will secure the door at this point in later steps. This is especially the case with high keyboards. You can also use a double-sided adhesive tape to hold it in place until you can fully secure the lock.

Some intelligent locks contain a steel or plastic plate that extends against the inside of the door. Take this and feed the wire from the front assembly. Then locate the two long screws and guide them through the other two holding the screw assembly on the front assembly. This locks everything in place.

For some latches, secure the inner assembly with the two long screws without the metal plate.

<img class = "wp-image-443993 size-full" data-pagespeed-lazy-src = "https://www.howtogeek.com/wp-content/uploads/2019/10/Install-Lock- Step-5a.jpg.pagespeed.ce.jjPPXHBuvz.jpg "alt =" A metal plate with two screws and a power cable plugged in. [19659002] Josh Hendrickson

Connect the wire from the outer piece to the inner assembly, usually the inner part Channels that guide the wiring and prevent jamming.

  An inner part wired to the rest of the lock.
Josh Hendrickson

When you have connected the cable, place the inner part on the door and secure it with Fasten screws.

  A close-up view of an impact Encode lock with stabilizing screws.
Josh Hendrickson

Now you only need to insert your batteries Door shows, it's normal s it is locked and unlocked multiple times as part of this process. Once this is done, you can pair your app and set up PINs if you have a keyboard.


Source link