You open youror the freezer door to grab something, close the door and come back later to see there's a gap. The door has not closed completely and now the food is not as cold as it should be.
It's a frustrating situation, but one that's not hard to fix. If the doors of your refrigerator do not close, you can do the following:
Common reasons why the door does not stay closed
You've already checked if anything in your refrigerator pushes against the door, but the door stops do not stay closed. There are few common (and easy to fix) reasons for this.
- There is too much weight in the door. Remove heavy objects like gallons of milk or juice to reduce weight.
- The fridge is not straight. If the front of the refrigerator is tilted forward, the doors will not remain closed. Use a step to check the refrigerator and then adjust your feet.
- The hinges are not aligned. Years of use can strain and pull down the hinges of your refrigerator. Tighten and adjust the hinges with a screwdriver.
If none of them is the culprit, it is time to check the door seal of your refrigerator.
Check the Seal
The seal around youror freezer door ̵
Your seals are not fancy. It's basically a rubber strip that fits snugly into a groove around the edge of the door. Sometimes the seal wiggles off the grove and just has to be pushed in again.
Take your hand and guide it along the edges of the door while it is closed. If you feel a little cold air, you have found the loose area. Use a cotton swab to press a little Vaseline into the groove under the loose rubber. This facilitates the pushing back of the rubber and helps to seal leaks. Then just push the gasket back into the duct.
Cleaning the seal
Sometimes, when a door does not close or strike by itself, the problem is a dirty seal. In a bowl, mix warm water with a drop of dishwashing detergent. Dip an old toothbrush into the mixture and use it to scrub the seal. Be sure to get the dirt on each side of the seal. Then wipe the gasket with a damp cloth.
To prevent dirt on the seal from ever being a problem again, wipe it off once a week.
More information: How often should you clean your refrigerator
Replace the old seal with a new one
Oftentimes, you just have to start fresh with a new seal. Every 12 months or so, make sure your refrigerator seals are in good condition. One way to determine if a seal is bad is to do the paper test. Place a piece of paper between the door and the refrigerator, close the door, and then pull. If the paper slips out easily, it's time to replace the seals because it's not sealed.
The seal is also no longer useful when it:
- Bent or bent at the corners
- Hard instead of flexible
A new seal is to be ordered easy. First, you need to know which brand and model of appliance you have. If you do not know, take a look at the back. Usually there is a sticker or sticker with the model number and other information.
Next, go to the manufacturers parts website, enter the information of your unit, and the seal you need should come directly. You can also go to your local workshop and order a replacement part for you.
Once you have the new seal, remove it from its packaging, place it in a sink or tub, and soak in warm water while removing the old seal. This makes it more flexible for installation and smoothes any bends caused by shipping.
Now there is no way to replace a gasket. Make sure you check your user manual (available on your refrigerator manufacturer's website) to make sure no additional steps are required. Some high-end devices have buttons, push buttons or extra grooves. I will give you the step-by-step process of replacing a more common type of gasket.
To remove the old seal, start at the top. Grab the edge on the inside of the door and pull it upwards. You should see a retaining plate, which is fastened with hexagon screws under the seal. Loosen the screws around the seal with a screwdriver. Then the seal should peel off properly.
If you do not see any screws, do not panic. Simply pull on the gasket until it pops out of the grooves.
The new seal is exactly the same, but in reverse order. Glue the longer lip of the gasket behind the holder or in the upper groove, starting with the corners. Once you have the lip all around the door, tighten the screws and tighten the gasket over them.
If there are no screws, there is a high likelihood that there will be a second groove in the front and your seal will have a smaller lip wedged in it.
Give the door a try. If it closes and you do not feel drafts, you were successful. When you feel a puff, make sure that your lip is behind the dealer's wall. You may need to loosen the screws near you and try to replace the lip. If there are any gaps or distortions, heat the seal with a hair dryer. This should put it in the right shape.
Read more: Here areYou can easily repair yourself.
31 foodstuffs that should always be kept refrigerated